Silicone molds are durable and flexible making them one of the best solutions if you are looking to make personalized products. These molds can be made in a variety of shapes and sizes. You can find them in varying shapes ranging from round to silicone molds mini, and it is one of the reasons why many industries lean towards silicone to make customized molds. If you are also planning on creating silicone molds for your business or for personal use, here is a guide that will help you make the best silicone molds according to your needs.
Things You Need For Large Silicone Mold Making
To create large and small silicone molds, you will need a few supplies. These supplies are readily available in the market and can be found at affordable prices. Mostly, Silicone molds are created through a chemical process. But, In order to understand the process, first, you should know about the types of silicone solutions.
There are two kinds of silicone solutions- single solution and two-part solution. A single solution is straightforward but takes longer to harden and is considered less reliable. This is why a two-part solution is usually preferred in the silicone mold-making process. Some solutions harden quickly while others require a little time. It is important to mix the right ingredients and solutions to produce the best molds as per your needs.
Materials You Need To Make Big Silicone Molds
Whether you are looking to make big or tiny silicone molds, you will need the same list of materials. First, you will need a two-part solution that comes with part A and part B, for the reaction to occur, the two must be combined in a 1:1 ratio. Before creating your molds, make sure to combine the components well and create a mixture. You will also need the following items:
Mold release: One of the main materials you need while making silicone molds is mold release, it is advised to add mold release in your mixture to ensure the easy removal of mold from the container.
Catalyst: Most solutions do not require a catalyst, but if you are making molds in a bulk, it will help you speed up the process without compromising the quality of the mold.
Coloring: You can give your molds a unique appntearance by adding some dye or colors to them. For instance, you can add differe dyes while making square silicone molds for ice cube trays to make them look distinctive.
Thickener: A thickener can help you thin out your solution and will make it more durable. It is important to keep in mind to add a limited amount of thickener as too much of it can disturb the consistency of the solution.
Thinner: If your solution becomes too thick, you can use a thinner to thin out your solution.
Razor knife: Once your solution is hardened and dried up, you will need a razor knife to cut off the extra edges of your round silicone molds.
The Process Of Making- Small To Big Silicone Molds
There are many factors to consider while making silicone molds. First, you should set up a workstation where you want to make your silicone molds. It is advised to cover the place with disposable plastic wrap and to wear disposable aprons or unimportant clothing to make sure the place stays clean and sanitized.
Then, you are required to consider the type of mold you want to make. Whether you want to make food-grade or non-food-grade molds. If you are planning on making non-food-grade molds you can use RTV silicone supplies for the best results.
While making silicone molds, it is advised to make a prior decision about the size of the mold so that you can take appropriate measurements of the solution. The simplest solution to make mini silicone molds is to place a canister that is of no use and to put the item at the bottom from which you want to make the cast.
Once you are done with the above steps, you can start mixing the solutions together. One thing to keep in mind while combining the solution is to never use the same container for mixing the solutions in which you want to create your mold. Always use a separate container for mixing the solutions. While creating big silicone molds, it is important to mix the appropriate quantity of the solution. Because a lack of solution can increase the completion time of the process. Once the silicone has hardened, it is time to cut out the mold from the container or turn the container upside down to let the mold fall out from it.
Takeaway
Creating your own silicone molds can be a challenge and requires great precision and accuracy. But with the help of the steps listed above, you can easily create small or large silicone molds according to your needs. But, if you are looking for a renowned company that makes the best-customized silicone molds, Custom Rubber Silicone Molds is the best place for you. Our specialized team will provide the best-customized molds according to your requirements and support all your specific needs
